3.5-Inch Lift Kit with V2 Shocks for Jeep Wrangler JK 4WD (2007–2017)
- Fits 2007–2017 Jeep Wrangler JK 4WD two-door models — does not fit 4-door
- 2012-2018 models need exhaust modification for front driveshaft clearance
- Kit contents: 3.5in 2-door kit box, 3.5in Vertex kit box, and two V2 monotube shock pairs
- Rear coil correction plates adjust coil spring angle by 10 degrees; drop brackets restore alignment
- Bolt-on install, no cutting — downloadable installation guide available
The Trail Fortress check
Will it fit your truck?
✓ Fits
✕ Does not fit
- 4-door models
2012-2018 models require exhaust modifications to clear the front driveshaft SKU: 1030. On Automatic equipped vehicles due to use of an oversize driveshaft from the factory and inadequate factory clearance it may be possible for the front driveshaft to come in contact with the automatic transmission pan tearing the factory boot and rubbing on the shaft. Generally this occurs during heavy articulation when front sway bar links are disconnected and longer shocks are installed. If this is found to occur the proper procedure would be to replace the oversize factory shaft with an aftermarket smaller diameter shaft to increase clearance between the transmission and front driveshaft. Rough Country does offer this driveshaft if needed. Fitment on this page is based on the manufacturer’s application data.
About this kit
3.5-Inch Lift Kit with V2 Shocks, fitment-checked
Rough Country 69370 is a 3.5-inch lift kit for 2007–2017 Jeep Wrangler JK 4WD two-door models, built around a Vertex kit box, control arm drop brackets, factory-rate coils, and two V2 monotube shock pairs. It does not fit 4-door models. On 2012-2018 vehicles, exhaust modification is needed for front driveshaft clearance.
This 3.5-inch lift kit for the 2007–2017 Jeep Wrangler JK 4WD covers Sport, Sport S, X, Sahara, Rubicon, and the 70th and 75th Anniversary two-door builds listed in the fitment section. Control arm drop brackets bring suspension geometry back in line, and rear coil correction plates reset the coil angle by 10 degrees. Coils are calibrated to the factory spring rate, and installation is bolt-on with no cutting. Automatic-equipped Jeeps can see front driveshaft-to-transmission-pan contact under heavy articulation with the sway bar links disconnected; review that note before ordering. A downloadable installation guide is available.
What’s in the box
Kit contents
- 1× 3.5in 2dr Kit Box 1608BOX1
- 1× 3.5in Vertex Kit Box 1693BOX2
- 1× V2 MONOTUBE SHOCK PAIR 760740-2
- 1× V2 MONOTUBE SHOCK PAIR 760750-2
Rough Country shares subassemblies across kits, so individual package labels can carry broader application ranges. The complete 69370 kit fits the vehicles shown in the fitment section above.
Specifications
Specs
| Brand | Rough Country |
| Part number | 69370 |
| UPC / GTIN | 00843030161446 |
| Lift height | 3.5 in |
| Shipping weight | 119.3 lb |
| Country of origin | US |
| Category | Suspension & Lift Kits › Lift Kits |
Why buy here
The fitment-first store
Keep looking
More Lift Kits
6 Inch
4 Inch
6 Inch
4 Inch
4 Inch
6 Inch
4 Inch
6 Inch
4 Inch
4 Inch
4 Inch
3.5 Inch
3.5 Inch
3.5 Inch
3.5 Inch
4 Inch