3.5-Inch Lift Kit with M1 Shocks for Wrangler Unlimited (2007-2017)
- Two M1 Monotube shock pairs plus the 3.5in Vertex kit box and Unlimited kit box
- Covers 2007-2017 Jeep Wrangler Unlimited trims from Sport through Rubicon — two-door models excluded
- Control arm drop brackets plus rear coil correction plates that shift coil angle 10 degrees
- Bolt-on install, no cutting; exhaust modification needed on 2012-2018 Jeeps for driveshaft clearance
- Automatic Jeeps with the oversize factory shaft may require replacement shaft part 1030
- Downloadable installation guide available; shipping weight: 120.8 lb
The Trail Fortress check
Will it fit your truck?
✓ Fits
✕ Does not fit
- 2-door models
2012-2018 models require exhaust modifications to clear the front driveshaft SKU: 1030. On Automatic equipped vehicles due to use of an oversize driveshaft from the factory and inadequate factory clearance it may be possible for the front driveshaft to come in contact with the automatic transmission pan tearing the factory boot and rubbing on the shaft. Generally this occurs during heavy articulation when front sway bar links are disconnected and longer shocks are installed. If this is found to occur the proper procedure would be to replace the oversize factory shaft with an aftermarket smaller diameter shaft to increase clearance between the transmission and front driveshaft. Rough Country does offer this driveshaft if needed. Fitment on this page is based on the manufacturer’s application data.
About this kit
3.5-Inch Lift Kit with M1 Shocks, fitment-checked
Two M1 Monotube shock pairs ship with this 3.5-inch lift kit for the 2007-2017 Jeep Wrangler Unlimited, packed alongside the Unlimited kit box and the 3.5in Vertex kit box. Four-door Unlimited models only — two-door Wranglers are not covered. Shipping weight: 120.8 lb.
The M1 Monotube damping is what sets this 3.5-inch lift kit for the 2007-2017 Jeep Wrangler Unlimited apart from the same-height kits in the range: front and rear shock pairs arrive in the box with the Vertex kit hardware. Control arm drop brackets bring suspension geometry back toward stock alignment, rear coil correction plates rotate the coil angle 10 degrees, and the springs hold the factory rate. Bolt-on, no cutting. Exhaust modification is required on 2012-2018 Jeeps for front driveshaft clearance, and automatic Jeeps running disconnected sway bar links may need the smaller-diameter shaft, part 1030.
What’s in the box
Kit contents
- 1× Unltd Kit Box 1609BOX4
- 1× 3.5in Vertex Kit Box 1693BOX2
- 1× M1 MONOTUBE SHOCK PAIR 770740P
- 1× M1 MONOTUBE SHOCK PAIR 770750P
Rough Country shares subassemblies across kits, so individual package labels can carry broader application ranges. The complete 69440 kit fits the vehicles shown in the fitment section above.
Specifications
Specs
| Brand | Rough Country |
| Part number | 69440 |
| UPC / GTIN | 00840269918650 |
| Lift height | 3.5 in |
| Shock package | M1 series |
| Shipping weight | 120.8 lb |
| Country of origin | US |
| Category | Suspension & Lift Kits › Lift Kits |
Why buy here
The fitment-first store
Keep looking
More Lift Kits
6 Inch
4 Inch
6 Inch
4 Inch
4 Inch
6 Inch
4 Inch
6 Inch
4 Inch
4 Inch
4 Inch
3.5 Inch
3.5 Inch
3.5 Inch
3.5 Inch
4 Inch